Історія версій TW Pearl Miner
6 версій, нові зверху. Описи наведено так, як їх опублікував розробник (англійською).
TW Pearl Miner 3.5.1 Поточна
Improved hashrate for H100
提昇了 H100的算力
| 檔案 / Asset | 用途 / Use |
|---|---|
tw-pearl-miner-3.5.1.tar.gz | Linux / HiveOS（驅動 580 以上 / driver ≥ 580） |
tw-pearl-miner-3.5.1.c12.tar.gz | Linux（舊驅動 / driver < 580） |
tw-pearl-miner-windows.zip | Windows |
TW Pearl Miner 3.5.0
⚠️Every miner must upgrade to v3.5.0 before block height 99000.**
From the fork height onward, older miners (v3.4.2 and every earlier version) produce shares that are 100% invalid
This version also optimized 50 series hashrate
⚠️所有礦工都必須在區塊高度 99000 之前升級到 v3.5.0。**
分叉生效後，舊版礦工（v3.4.2 以前，含全部舊版本）算出來的份額100% 無效，礦池會全部拒絕
這個版本也優化了50系列的算力
⚠️ Keep the package files intact (applies to every version)
The miner verifies the release signature at startup. It will not start if any of these are missing — do not delete, rename or move them:
pearl-gpu-miner pearl.guard pearl-release.json
pearl-release.sig pearl-policy.enc libpearlkernel.so.enc
libcudart.so.13 pearl-verify
⚠️ 檔案請保持完整（每版適用）
礦工啟動時會驗證發布包的簽章，下列檔案缺任何一個都無法啟動，請不要刪除、改名或搬走：
pearl-gpu-miner pearl.guard pearl-release.json
pearl-release.sig pearl-policy.enc libpearlkernel.so.enc
libcudart.so.13 pearl-verifyTW Pearl Miner 3.4.2
- Increase performance for 30 series by 6-8%
- Increase performance for 4070 super , if you encounter any dropped hashrate with 4070 super , try --direct b-only or --direct off
- 30系列優化
- 修正了4070 super的算力, 如果在4070 super上遇到算力不正常下降的問題, 請使用 --direct b-only 或 --direct off
⚠️ Keep the package files intact (applies to every version)
The miner verifies the release signature at startup. It will not start if any of these are missing — do not delete, rename or move them:
pearl-gpu-miner pearl.guard pearl-release.json
pearl-release.sig pearl-policy.enc libpearlkernel.so.enc
libcudart.so.13 pearl-verify
⚠️ 檔案請保持完整（每版適用）
礦工啟動時會驗證發布包的簽章，下列檔案缺任何一個都無法啟動，請不要刪除、改名或搬走：
pearl-gpu-miner pearl.guard pearl-release.json
pearl-release.sig pearl-policy.enc libpearlkernel.so.enc
libcudart.so.13 pearl-verify
TW Pearl Miner 3.4.1
- Increase hashrate for 40/50 series
- Dev fee stays at the standard rate.
- Windows:
tw-pearl-miner-windows.zip. - Driver below 580: use
tw-pearl-miner-3.4.1.c12.tar.gz(CUDA 12).
- 40/50系列優化
- 開發費 1.5%，與先前版本相同。
- Windows 版本：
tw-pearl-miner-windows.zip。 - 驅動版本低於 580 請使用
tw-pearl-miner-3.4.1.c12.tar.gz（CUDA 12）。
⚠️ Keep the package files intact (applies to every version)
The miner verifies the release signature at startup. It will not start if any of these are missing — do not delete, rename or move them:
pearl-gpu-miner pearl.guard pearl-release.json
pearl-release.sig pearl-policy.enc libpearlkernel.so.enc
libcudart.so.13 pearl-verify
⚠️ 檔案請保持完整（每版適用）
礦工啟動時會驗證發布包的簽章，下列檔案缺任何一個都無法啟動，請不要刪除、改名或搬走：
pearl-gpu-miner pearl.guard pearl-release.json
pearl-release.sig pearl-policy.enc libpearlkernel.so.enc
libcudart.so.13 pearl-verify
TW Pearl Miner 3.4.0
- 優化了 20/30/40/50 卡的算力
- Windows 版本：
tw-pearl-miner-windows.zip。 - 驅動版本低於 580 請使用
tw-pearl-miner-3.4.0.c12.tar.gz（CUDA 12）。
- Improved hashrate on 20/30/40/50 series card
- Windows:
tw-pearl-miner-windows.zip. - Driver below 580: use
tw-pearl-miner-3.4.0.c12.tar.gz(CUDA 12).
⚠️ 檔案請保持完整（每版適用）
pearl-gpu-miner pearl.guard pearl-release.json
pearl-release.sig pearl-policy.enc libpearlkernel.so.enc
libcudart.so.13 pearl-verify
可以安全刪除或自行修改（HiveOS / MMPOS 專用，一般 Linux 直接執行用不到）： start.sh、h-config.sh、h-run.sh、h-stats.sh、h-manifest.conf、mmp-external.conf、mmp-launch.sh、mmp-stats.sh。 在礦工資料夾裡放自己的設定檔、log、腳本或子資料夾都沒問題。
升級請整包解壓縮到同一個資料夾，不要只覆蓋 pearl-gpu-miner。 v3.2.2 與最初的 v3.3.0 沒有 pearl.guard，只換執行檔會出現：
Error: signed release verification failed: release verification I/O error:
.../pearl.guard: No such file or directory (os error 2)
補回上面清單中缺少的檔案即可，不需要重裝。
⚠️ Keep the package files intact (applies to every version)
The miner verifies the release signature at startup. It will not start if any of these are missing — do not delete, rename or move them:
pearl-gpu-miner pearl.guard pearl-release.json
pearl-release.sig pearl-policy.enc libpearlkernel.so.enc
libcudart.so.13 pearl-verify
Safe to delete or edit (HiveOS / MMPOS only — not used when running on plain Linux): start.sh, h-config.sh, h-run.sh, h-stats.sh, h-manifest.conf, mmp-external.conf, mmp-launch.sh, mmp-stats.sh. Your own config files, logs, scripts and sub-folders in the miner directory are fine.
When upgrading, extract the WHOLE package into the folder — do not copy only pearl-gpu-miner. v3.2.2 and the original v3.3.0 had no pearl.guard, so replacing just the executable gives:
Error: signed release verification failed: release verification I/O error:
.../pearl.guard: No such file or directory (os error 2)
Restoring the missing files from the archive fixes it — no reinstall needed.
TW Pearl Miner 3.3.3
v3.3.0 / v3.3.1 / v3.3.2 的使用者請務必升級到本版。
- 修正 8GB 以下顯卡完全無法啟動的問題。 v3.3.x 把預設 rank 改為 128 之後，8GB 以下的卡會按全常駐規劃記憶體（約 10.3 GiB），結果全部在初始化階段被丟棄，畫面顯示
FAILED to initialize — DROPPED以致ALL n GPU(s) failed。受影響的包含 RTX 4060 / 5060 / 3060 / 3060 Ti / 3070 等所有 8GB 與 6GB 卡（有回報一台 7 卡機七張全掉）。本版起這些卡改用串流模式，與 v3.2.2 的行為一致。 - 修正 aonly 加速在 rank-128 預設下失效：分叉後未建立per-card 計畫，導致 aonly 全機隊靜默關閉。本版重新啟用，沿用 v3.2.2 的同一組 ship table 與 VRAM 門檻。
- RTX 40 系（sm_89）rank-128 核心調校：4090 實測 266.8 → 約 278 TH/s。
- Windows 版本：
tw-pearl-miner-windows.zip。 - 驅動版本低於 580 請使用
tw-pearl-miner-3.3.3.c12.tar.gz（CUDA 12）。
If you are on v3.3.0, v3.3.1 or v3.3.2, please upgrade.
- Fixes cards with 8GB or less failing to start entirely. Once v3.3.x made rank 128 the default, cards with 8GB or less planned memory fully resident (~10.3 GiB) and were all dropped during init —
FAILED to initialize — DROPPED, thenALL n GPU(s) failed. This affected every 8GB and 6GB card: RTX 4060 / 5060 / 3060 / 3060 Ti / 3070 and similar (one reported 7-GPU rig lost all seven). These cards now stream, the same as they did on v3.2.2. - Fixes the aonly speed-up switching itself off at the rank-128 default: no per-device plan was built after the fork, so aonly silently disengaged fleet-wide. Re-enabled using the same ship table and VRAM guards as v3.2.2.
- RTX 40-series (sm_89) rank-128 kernel tuned: measured 266.8 → ~278 TH/s on a 4090.
- Windows:
tw-pearl-miner-windows.zip. - Driver below 580: use
tw-pearl-miner-3.3.3.c12.tar.gz(CUDA 12).
⚠️ 檔案請保持完整（每版適用）
礦工啟動時會驗證發布包的簽章，下列檔案缺任何一個都無法啟動，請不要刪除、改名或搬走：
pearl-gpu-miner pearl.guard pearl-release.json
pearl-release.sig pearl-policy.enc libpearlkernel.so.enc
libcudart.so.13 pearl-verify
可以安全刪除或自行修改（HiveOS / MMPOS 專用，一般 Linux 直接執行用不到）： start.sh、h-config.sh、h-run.sh、h-stats.sh、h-manifest.conf、mmp-external.conf、mmp-launch.sh、mmp-stats.sh。 在礦工資料夾裡放自己的設定檔、log、腳本或子資料夾都沒問題。
升級請整包解壓縮到同一個資料夾，不要只覆蓋 pearl-gpu-miner。 v3.2.2 與最初的 v3.3.0 沒有 pearl.guard，只換執行檔會出現：
Error: signed release verification failed: release verification I/O error:
.../pearl.guard: No such file or directory (os error 2)
補回上面清單中缺少的檔案即可，不需要重裝。
⚠️ Keep the package files intact (applies to every version)
The miner verifies the release signature at startup. It will not start if any of these are missing — do not delete, rename or move them:
pearl-gpu-miner pearl.guard pearl-release.json
pearl-release.sig pearl-policy.enc libpearlkernel.so.enc
libcudart.so.13 pearl-verify
Safe to delete or edit (HiveOS / MMPOS only — not used when running on plain Linux): start.sh, h-config.sh, h-run.sh, h-stats.sh, h-manifest.conf, mmp-external.conf, mmp-launch.sh, mmp-stats.sh. Your own config files, logs, scripts and sub-folders in the miner directory are fine.
When upgrading, extract the WHOLE package into the folder — do not copy only pearl-gpu-miner. v3.2.2 and the original v3.3.0 had no pearl.guard, so replacing just the executable gives:
Error: signed release verification failed: release verification I/O error:
.../pearl.guard: No such file or directory (os error 2)
Restoring the missing files from the archive fixes it — no reinstall needed.
