PhoenixMiner — Eksiksiz kılavuz
PhoenixMiner'ın, Claymore's dual Ethereum miner'ın komut satırı seçeneklerinin çoğunu desteklediğini unutmayın;
bu nedenle Claymore'un madenci yazılımında kullanacağınız komut satırı seçeneklerinin aynısını kullanabilirsiniz.
Havuz seçenekleri:
-pool <host:port> Ethash pool address (prepend the host name with ssl:// for SSL pool, or http:// for solo mining)
-wal <wallet> Ethash wallet (some pools require appending of user name and/or worker)
-pass <password> Ethash password (most pools don't require it, use 'x' as password if unsure)
-worker <name> Ethash worker name (most pools accept it as part of wallet)
-proto <n> Selects the kind of stratum protocol for the ethash pool:
1: miner-proxy stratum spec (e.g. coinotron)
2: eth-proxy (e.g. dwarfpool, nanopool) - this is the default, works for most pools
3: qtminer (e.g. ethpool)
4: EthereumStratum/1.0.0 (e.g. nicehash)
5: EthereumStratum/2.0.0
-coin <coin> Ethash coin to use for devfee to avoid switching DAGs:
auto: Try to determine from the pool address (default)
eth: Ethereum
etc: Ethereum Classic
exp: Expanse
music: Musicoin
ubq: UBIQ
pirl: Pirl
ella: Ellaism
etp: Metaverse ETP
whale: WhaleCoin
vic: Victorium
nuko: Nekonium
mix: Mix
egem: EtherGem
etz: EtherZero
clo: Callisto
dbix: DubaiCoin
moac: MOAC
etho: Ether-1
yoc: Yocoin
b2g: Bitcoiin2Gen
esn: Ethersocial
ath: Atheios
reosc: REOSC
qkc: QuarkChain
bci: Bitcoin Interest
-stales <n> Submit stales to ethash pool: 1 - yes (default), 0 - no
-weakssl Skip the strict SSL certificate validation for the main ethash pool (the one specified with the -pool option)
-pool2 <host:port> Failover ethash pool address. Same as -pool but for the failover pool
-wal2 <wallet> Failover ethash wallet (if missing -wal will be used for the failover pool too)
-pass2 <password> Failover ethash password (if missing -pass will be used for the failover pool too)
-worker2 <name> Failover ethash worker name (if missing -worker will be used for the failover pool too)
-proto2 <n> Failover ethash stratum protocol (if missing -proto will be used for the failover pool too)
-coin2 <coin> Failover devfee Ethash coin (if missing -coin will be used for the failover pool too)
-stales2 <n> Submit stales to the failover pool: 1 - yes (default), 0 - no
-weakssl2 Skip the strict SSL certificate validation for the failover ethash pool (the one specified with the -pool2 option)
-dpool <host:port> Dual mining pool address
-dwal <wallet> Dual mining wallet
-dpass <password> Dual mining pool password (most pools don't require it, use 'x' as password if unsure)
-dworker <name> Dual mining worker name
-dcoin blake2s Currently only the Blake2s algorithm is supported for dual mining. If you want to put
all dual mining pools in dpools.txt, you need to set -dcoin blake2s in the command-line or in config.txt
to force the miner to load the dual mining pools from dpools.txt
-dstales <n> Submit stales to the dual mining pool: 1 - yes (default), 0 - no
Genel havuz seçenekleri:
-fret <n> Switch to next pool afer N failed connection attempts (default: 3)
-ftimeout <n> Reconnect if no new ethash job is receved for n seconds (default: 600)
-ptimeout <n> Switch back to primary pool after n minutes. This setting is 30 minutes by default;
set to 0 to disable automatic switch back to primary pool.
-retrydelay <n> Seconds to wait before reconnecting (default: 20)
-gwtime <n> Recheck period for Solo/GetWork mining (default: 200 ms)
-rate <n> Report hashrate to the pool: 1 - yes, 0 - no (1 is the default), 2 - (for solo mining only)
use alternative name of the report method "eth_submitHashRate" instead of "eth_submitHashrate"
-nosni Do not send SNI host name on SSL connections
Benchmark modu:
-bench [<n>],-benchmark [<n>] Benchmark mode, optionally specify DAG epoch. Use this to test your rig.
If you specify only the -bench option, you will benchmark the ethash algorithm. If you want to bench
the dual mining, use the options -bench <n> -dcoin blake2s. If you want to benchmark the ProgPOW BCI
algorithm, use the options -bench <n> -coin bci
Uzaktan kontrol seçenekleri:
-cdm <n> Selects the level of support of the CDM remote monitoring:
0: disabled
1: read-only - this is the default
2: full (only use on secure connections)
-cdmport <port> Set the CDM remote monitoring port (default is 3333). You can also specify
<ip_addr:port> if you have a secure VPN connection and want to bind the CDM port to it
-cdmpass <pass> Set the CDM remote monitoring password
-cdmrs Reload the settings if config.txt is edited/uploaded remotely. Note that most options require restart in order to change.
Currently the follwing options can be changed without restarting: -mi, -gt, -sci, -clf, -nvf, -gpow, and most of the
hardware control parameters (-tt, -fcm, -fanmin, -fanmax, -powlim, -tmax, -ttli, -cclock, -cvddc, -mclock,
-mvddc, -ppf, -straps, -vmt1, -vmt2, -vmt3, -vmr)
Madencilik seçenekleri:
-amd Use only AMD cards
-acm Turn on AMD compute mode on the supported GPUs. This is equivalent of pressing 'y' in the miner console.
-nvidia Use only Nvidia cards
-nvmalt Use alternative NVML initialization. Use this option if the program crashes or exits while showing Initializing NVML... on the console.
-gpus <123 ..n> Use only the specified GPUs (if more than 10, separate the indexes with comma)
-mi <n> Set the mining intensity (0 to 14; 12 is the default for the new kernels). You may specify this option per-GPU.
-gt <n> Set the GPU tuning parameter (6 to 400). The default is 15. You can change the
tuning parameter interactively with the '+' and '-' keys in the miner's console window.
If you don't specify -gt or you specify value 0, the miner will start auto-tuning to determine the best GT value for each GPU
Note that when the GPU is dual-mining, it ignores the -gt values, and uses -sci instead.
-sci <n> Set the dual mining intensity (1 to 1000). The default is 30. As you increase the value of -sci,
the secondary coin hashrate will increase but the price will be higher power consumption and/or
lower ethash hashrate.
You can change the this parameter interactively with the '+' and '-' keys in the miner
console window. You may specify this option per-GPU. If you set -sci to 0,
the miner will use auto-tuning to determine the best value, while trying to maximize the
ethash hashrate regardless of the secondary coin hashrate.
-clkernel <n> Type of OpenCL kernel: 0 - generic, 1 - optimized, 2 - alternative, 3 - turbo (1 is the default)
-clgreen <n> Use the power-efficient ("green") kernels (0: no, 1: yes; default: 0).
You may specify this option per-GPU. Note that you have to run auto-tune again as the
optimal GT values are completely different for the green kernels
-clnew <n> Use the new AMD kernels (0: no, 1: yes; default: 1)
-clabi <n> Use OpenCL 1.x even if 2.x is supported by the driver (0: no, 1: yes; default: 0)
-clf <n> AMD kernel sync (0: never, 1: periodic; 2: always; default: 1)
-nvkernel <n> Type of Nvidia kernel: 0 auto (default), 1 old (v1), 2 newer (v2), 3 latest (v3).
Note that v3 kernels are only supported on GTX10x0 GPUs. Also note that dual mining is
supported only by v2 kernels. You may specify this option per-GPU.
-nvdo <n> Enable Nvidia driver-specific optimizations (0 - no, the default; 1 - yes). Try -nvdo 1 if your
are unstable. You may specify this option per-GPU.
-nvnew <n> Use new Nvidia kernels if supported (0: no, 1: yes; default: 1)
-nvf <n> Nvidia kernel sync (0: never, 1: periodic; 2: always; 3: forced; default: 1). You may specify this option per-GPU.
-lhr <n> Nvidia LHR unlock (0: no, -1: automatic, 100-1000: unlock intensity; default: -1).
If this option is not specified (or specified as -1), the default LHR unlock intensity is 520. You may specify this option per-GPU.
-mode <n> Mining mode (0: dual mining if dual pool(s) are specified; 1: ethash only even if dual pools are specified).
You may specify this option per-GPU.
-list List the detected GPUs devices and exit
-gbase <n> Set the index of the first GPU (0 or 1, default: 1)
-minRigSpeed <n> Restart the miner if avg 5 min speed is below <n> MH/s
-eres <n> Allocate DAG buffers big enough for n epochs ahead (default: 2) to
avoid allocating new buffers on each DAG epoch switch, which should improve DAG switch stability
-daglim <n>
(AMD Polaris, Baffin, Tonga, or Fiji cards only) Limit the DAG size to <n> MB to allow mining on 4 GB cards a few weeks after epoch 373
on Windows (or 381 on Linux). The possible values except the exact DAG limit are also 0 (turn off the DAG limit), 1 (automatic DAG
limit size, usually 4023 MB under Windows; this is the default). Note that the hashrate will drop significantly with each epoch
after the DAG limit is in effect. If the hashrate drops too much (e.g. from 28 MH/s to just 2-3 MH/s, you need to use lower value,
for example "-daglim 3996" or even lower.
-dagrestart <n> Restart the miner when allocating buffer for a new DAG epoch. The
possible values are: 0 - never, 1 - always, 2 - auto (the miner decides depending on the driver version).
This is relevant for 4 GB AMD cards, which may have problems with new DAG epochs after epoch 350.
-lidag <n> Slow down DAG generation to avoid crashes when swiching DAG epochs
(0-3, default: 0 - fastest, 3 - slowest).
-gser <n> Serializing DAG creation on multiple GPUs (0 - no serializing, all GPUs generate the DAG simultaneously, this is the default;
1 - partial overlap of DAG generation on each GPU; 2 - no overalp (each GPU waits until the previous one has finished generating the DAG);
3-10 - from 1 to 8 seconds delay after each GPU DAG generation before the next one)
-gpureset <n> Fully reset GPU when paused (0 - no, 1 - yes; default: no, except on 1080Ti). You may specify this option per-GPU.
-altinit Use alternative way to initialize AMD cards to prevent startup crashes
-rvram <n> Minimum free VRAM in MB (-1: don't check; default: 384 for Windows, and 128 for Linux)
-wdog <n> Enable watchdog timer: 1 - yes, 0 - no (1 is the default). The watchdog timer checks
periodically if any of the GPUs freezes and if it does, restarts the miner (see the -rmode
command-line parameter for the restart modes)
-wdtimeout <n> Watchdog timeout (30 - 300; default 45 seconds). You can use this parameter to increase
the default watchdog timeout in case it restarts the miner needlessly
-rmode <n> Selects the restart mode when a GPU crashes or freezes:
0: disabled - miner will shut down instead of restarting
1: restart with the same command line options - this is the default
2: reboot (shut down miner and execute reboot.bat)
-log <n> Selects the log file mode:
0: disabled - no log file will be written
1: write log file but don't show debug messages on screen (default)
2: write log file and show debug messages on screen
-logfile <name> Set the name of the logfile. If you place an asterisk (*) in the logfile name, it will be
replaced by the current date/time to create a unique name every time PhoenixMiner is started. If there
is no asterisk in the logfile name, the new log entries will be added to end of the same file. If you
want to use the same logfile but the contents to be overwritten every time when you start the miner,
put a dollar sign ($) character in the logfile name (e.g. -logfile my_log.txt$).
-logdir <path> Set a path where the logfile(s) will be created
-logsmaxsize <n> Maximum size of the logfiles in MB. The default is 200 MB (use 0 to turn off the limitation).
On startup, if the logfiles are larger than the specified limit, the oldest are deleted. If you use a
single logfile (by using -logfile), then it is truncated if it is bigger than the limit and a new one
is created.
-config <name> Load a file with configuration options that will be added to the command-line options.
Note that the order is important. For example, if we have a config.txt file that contains -cclock 1000
and we specify command line -cclock 1100 -config config.txt, the options from the config.txt file will take
precedence and the resulting -cclock will be 1000. If the order is reversed (-config config.txt -cclock 1100)
then the second option takes precedence and the resulting -cclock will be 1100. Note that only one -config
option is allowed. Also note that if you reload the config file with 'c' key or with the remote interface,
its options will take precedence over whatever you have specified in the command-line.
-timeout <n> Restart miner according to -rmode after n minutes
-pauseat <hh:mm> Pause the miner at hh::mm (24 hours time). You can specify multiple times: -pauseat 6:00,12:00
-resumeat <hh:mm> Resume the miner at hh::mm (24 hours time). You can specify multiple times: -resumeat 8:00,22:00
-gswin <n> GPU stats time window (5-30 sec; default: 15; use 0 to revert to pre-2.8 way of showing momentary stats)
-gsi <n> Speed stats interval (5-30 sec; default: 5; use 0 to disable). The detailed stats are still
shown every 45 seconds and aren't affected by the -gsi value
-astats <n> Show advanced stats from Web sources (0: no; 1: yes). By default the coin exchange rates are updated every
4 hours, and the coin difficulty is updated every 8 hours. You can increase these periods by specifying
for example -astats 12, which will increase update periods to 12 and 24 hours respectively
-gpow <n> Lower the GPU usage to n% of maximum (default: 100). If you already use -mi 0 (or other low value) use -li instead
-li <n> Another way to lower the GPU usage. Bigger n values mean less GPU utilization; the default is 0.
-resetoc Reset the hardware overclocking settings on startup
-leaveoc Do not reset overclocking settings when closing the miner
Donanım kontrol seçenekleri; her GPU için farklı değerler belirtmek için virgül kullanın:
-tt <n> Set fan control target temperature (special values: 0 - no HW monitoring on ALL cards,
1-4 - only monitoring on all cards with 30-120 seconds interval, negative - fixed fan speed at n %)
-ttj <n> Set fan control target hotspot (junction) temperature (can be used
only on GPUs that report the junction temperature). Example: -ttj 75 will keep the junction temperature at or bellow 75C by
increasing the fan speed as necessary. This parameter can be combined with -tt, and -ttmem
-ttmem <n> Set fan control target video memory temperature (can be used only
on GPUs that report the VRAM temperature). Example: -ttmem 83 will keep the GPU memory temperature at or
bellow 83C by increasing the fan speed as necessary. This parameter can be combined with -tt, and -ttj
-hstats <n> Level of hardware monitoring: 0 - temperature and fan speed only; 1 - temperature, fan speed, and power;
2 - full (include core/memory clocks, voltages, P-states). The default is 1.
-pidle <n> Idle power consumption of the rig in W. Will be added to the GPU power consumption when
calculating the total power consumption of the rig.
-ppf <n> The power usage of each GPU will be multiplied by this value to get the actual usage. This value is
in percent, so for example if the GPU reports 100 W power usage and you have specified -ppf 106 the GPU
power usage will be calculated to be 100 * (106 / 100) = 106 W. This allows you to correct for the efficiency
of the PSUs and the individual GPUs. You can also specify this value for each GPU separately.
-prate <n> Price of the electricity in USD per kWh (e.g. -prate 0.1). If specified the miner will calculate the
rig daily electricity cost
-fanmin <n> Set fan control min speed in % (-1 for default)
-fanmax <n> Set fan control max speed in % (-1 for default)
-fanstop <n> (AMD cards under Windows only) If set to 0 (the default), and a
fixed fan speed (e.g. -tt -40), or -fanmin is used, the miner will not allow the fans to stop rotating.
If set to 1, PhoenixMiner will not interfere in the fan stop function of the card.
-fcm <n> Set fan control mode (0 - auto, 1 - use VBIOS fan control, 2 - forced fan control; default: 0)
-tmax <n> Set fan control max temperature (0 for default)
-powlim <n> Set GPU power limit in % (from -75 to 75, 0 for default)
-cclock <n> Set GPU core clock in MHz (0 for default). For Nvidia cards use relative values (e.g. -300 or +400)
-cvddc <n> Set GPU core voltage in mV (0 for default). For Nvidia cards use relative values (e.g. -300 or +400)
-mclock <n> Set GPU memory clock in MHz (0 for default)
-mvddc <n> Set GPU memory voltage in mV (0 for default)
-tstop <n> Pause a GPU when temp is >= n deg C (0 for default; i.e. off)
-tstart <n> Resume a GPU when temp is <= n deg C (0 for default; i.e. off)
-mt <n> VRAM timings (AMD under Windows only): 0 - default VBIOS values; 1 - faster timings; 2 - fastest timings.
The default is 0. This is useful for mining with AMD cards without modding the VBIOS. If you have modded BIOS,
it is probably faster than even -mt 2
-leavemt Do not reset memory timing level ("-mt") to 0 when closing
-ttli <n> Lower GPU usage when GPU temperature is above n deg C. The default value is 0, which means do not lower the usage regardless of the
GPU temperature. This option is useful whenever -tmax is not working. If you are using both -tt and -ttli options, the
temperature in -tt should be lower than the -ttli to avoid throttling the GPUs without using the fans to properly cool them first.
-tmaxj <n> Lower GPU usage when hotspot (junction) temperature is above n deg C (can be used only on GPUs that report the junction temperature).
The default value is 0, which means do not lower the usage regardless of the GPU hotspot temperature. If you are using both
-ttj and -tmaxj options, the temperature in -ttj should be lower than the -tmaxj to avoid throttling the GPUs without using
the fans to properly cool them first.
-tmaxmem <n> Lower GPU usage when VRAM temperature is above n deg C (can be used only on GPUs that report the memory temperature).
The default value is 0, which means do not lower the usage regardless of the GPU memory temperature. If you are using both
-ttmem and -tmaxmem options, the temperature in -ttmem should be lower than the -tmaxmem to avoid throttling the GPUs
without using the fans to properly cool them first.
-straps <n> Memory strap level (Nvidia cards 10x0 and P10x series only). The possible values are 0 to 6. 0 is the default value and uses the default
timings from the VBIOS. Each strap level corresponds to a predefined combination of memory timings (-vmt1, -vmt2,
-vmt3, -vmr). Strap level 3 is the fastest predefined level and may not work on most cards, 1 is the slowest (but still faster than
the default timings). Strap levels 4 to 6 are the same as 1 to 3 but with less aggressive refresh rates (i.e. lower "-vmr" values).
-straps <n> Memory strap level (AMD Vega cards only). The possible values are 0 to 5. 0 is the default value and uses the default timings from the
VBIOS. Each strap level corresponds to a predefined combination of memory timings. Strap level 5 is the fastest level and may not work
on most cards, 1 is the slowest (but still faster than the default timings). Note that straps for AMD cards are experimental and may
lead to crashes or instability. "-vmt1", "-vmt2", and "-vmt3" parameters have no effect on AMD cards
-vmt1 <n> Memory timing parameter 1 (0 to 100, default 0)
-vmt2 <n> Memory timing parameter 2 (0 to 100, default 0)
-vmt3 <n> Memory timing parameter 3 (0 to 100, default 0)
-vmr <n> Memory refresh rate (0 to 100, default 0). For AMD cards you may also use "-rxboost"
-nvmem <n> Force using straps on unsupported Nvidia GPUs (0 - do not force, 1 - GDDR5, 2 - GDDR5X). Make sure that the parameter matches your GPU
memory type. You can try this if your card is Pascal-based but when you try to use -straps or any other memory timing option, the card
is shown as "unsupported".
-rxboost <n> Memory refresh rate on AMD cards (0 - default values, 1 - predefined value that should work on most cards, 2 to 100 -
increasingly aggressive settings). If you want to fine tune the value, you may run the miner with "-rxboost 1", write down the
corresponding "-vmr" values that are showed in the log file, and then use "-vmr" instead with adjusted values.
-vmdag <n> Reset straps to default during DAG generation (default: 1)
-mcdag <n> Reset GPU memory clock to default during DAG generation. Nvidia
only, default: 0 (turned off). This may allow you to set higher memory overclock on your Nvidia cards without risking corrupt DAG
buffer, which can lead to excessive number of stale shares.
Under Linux this option will execute the daggen.sh script (if present in the current directory) for each GPU, passing the GPU
index as the first argument, and PCIE bus ID as second argument. The miner will not wait for the daggen.sh script to finish before
starting to generate the DAGs. Instead it will for a fixed 7 seconds. This allows you to do all the following in the
daggen.sh: turn off the overclocking of Nvidia GPUs, sleep for 30-60 seconds, and then re-apply the overclocking of the Nvidia GPUs.
Genel seçenekler:
-v,--version Show the version and exit -vs Show short version string (e.g. "4.1c") and exit -h,--help Show information about the command-line options and exit
GPU başına seçenekler
PhoenixMiner seçeneklerinin bazıları ya tüm GPU'lar için aynı ayarı ya da her GPU için farklı
bir ayarı verebilir. Örneğin -gt değerini tüm kartlar için belirtmek isterseniz
-gt 90 yazarsınız, ancak her kart için farklı bir GT değeri belirtmek istiyorsanız şuna benzer bir şey kullanın:
beş GPU'lu bir madencilik rig'i için -gt 20,15,40,90,90. Bu, GT'yi ilk GPU için 20'ye, ikinci GPU için
15'e ayarlar ve bu böyle devam eder. GPU sayınızdan daha az değer belirtirseniz kalan GPU'lar parametrenin varsayılan
değerini kullanır.
Farklı kartlar için farklı değerler belirtmenin başka, daha esnek bir yolunu da kullanabilirsiniz.
Bunu en iyi bir örnekle açıklayabiliriz: -cclock *:1100,1-3:1090,4:1300 - burada çekirdek frekansını
1 ile 3 arasındaki kartlar (1090 MHz'e ayarlanır) ve 4. kart (1300 MHz) dışındaki tüm kartlar için 1100 MHz'e ayarlıyoruz.
İki noktadan (:) önceki kısım seçicidir; iki noktadan sonraki değerin uygulanacağı GPU'ları seçer. Seçici şunlar olabilir:
- single GPU index: e.g. 5:1000 sets 1000 for the 5th GPU
- range of GPU indexes: e.g 2-5:1200 sets 1200 for the GPUs 2,3,4, and 5
- asterisk, which sets the value for all GPUs
- label amd or nvidia: e.g. amd:1090 sets the value to 1090 for all AMD cards
- arbitrary string that starts with letter and can contain letters, numbers and asterisks,
which is matched with the GPU name as listed by PhoenixMiner. Example: gtx*1070:+500 will
set value +500 for all cards which contain 'gtx' and '1070' in their names with anything
between them. This will match 'Nvidia GeForce GTX 1070' but not 'Nvidia GeForce 1070'.
Belirli bir karta birden fazla seçici uyuyorsa yalnızca sonuncusunun geçerli olduğunu unutmayın.
Örnek: -cclock *:1100,1-4:1090,2:1300, 2. kartı 1300'e; 1, 3 ve 4. kartları 1090'a;
kalan kartları ise 1100 MHz çekirdek frekansına ayarlar.
Ayrıca madenci yazılımı çalışırken konsol penceresinde şu tuşlardan birine basarak aşağıdaki etkileşimli komutları
kullanabilirsiniz:
s Print detailed statistics 1-9 Pause/resume GPU1 ... GPU9 (if you have more than 9 GPUs, type 010 for card 10, 011 for card 11, etc.) p Pause/resume the whole miner +,- Increase/decrease GPU tuning parameter g Reset the GPU tuning parameter (and stop auto-tuning if active) x Select the GPU(s) for manual or automatic GT tuning z Start AMD auto-tune process r Reload epools.txt and switch to primary ethash pool e Select the current ethash pool (if you have more than 9 pools in the list, type 010 for pool 10, 011 for pool 11, etc.) d Select the current dual-mining pool y Turn on AMD Compute mode if it is off on some of the GPUs c Reload the config.txt file (some settings require restart, see -cdmrs option above for details) h Print this short help
Yapılandırma dosyaları
PhoenixMiner'ın Claymore's dual Ethereum miner ile aynı yapılandırma dosyalarını desteklediğini unutmayın;
bu nedenle mevcut yapılandırma dosyalarınızı hiçbir değişiklik yapmadan kullanabilirsiniz.
Komut satırı seçenekleri yerine PhoenixMiner'ı yapılandırma dosyalarıyla da
kontrol edebilirsiniz. PhoenixMiner.exe'yi hiçbir seçenek olmadan çalıştırırsanız, geçerli dizinde
config.txt dosyasını arar ve komut satırı seçeneklerini ondan okur. İsterseniz PhoenixMiner.exe'yi
çalıştırırken tek komut satırı seçeneği olarak başka bir dosyanın adını belirterek
o dosyayı kullanabilirsiniz.
Örnek bir config.txt dosyasını PhoenixMiner'ın dizininde bulabilirsiniz.
Havuz(lar)ı doğrudan komut satırında belirtmek yerine bunun için epools.txt adlı başka bir
yapılandırma dosyası kullanabilirsiniz. Orada her satıra bir havuz belirtebilirsiniz (örnek bir
epools.txt dosyasını PhoenixMiner'ın dizininde bulabilirsiniz).
Dual madencilik havuzları için, epools.txt ile aynı biçime sahip olan ancak ikincil coin'e
yönelik dpools.txt dosyasını kullanabilirsiniz. Örnek bir epools.txt dosyasını PhoenixMiner'ın dizininde bulabilirsiniz.
Madenci yazılımı her başladığında yüklenen epools.txt'nin aksine, dpools.txt dosyasının
yalnızca komut satırında -dpool ile bir dual madencilik havuzu belirtirseniz ya da en azından
-dcoin blake2s komut satırı seçeneğini eklerseniz okunduğunu unutmayın.
config.txt ve epools.txt/dpools.txt dosyalarını kullanmanın avantajları şunlardır:
- Birden fazla rig'iniz varsa bu dosyalarla tüm ayarları kopyalayıp yapıştırabilirsiniz
- Rig'lerinizi uzaktan kontrol ediyorsanız, madenci yazılımına yeni epools.txt dosyaları yükleyerek
havuzları, hatta yeni bir config.txt dosyası yükleyip madenci yazılımını yeniden başlatarak
madenci yazılımı seçeneklerini değiştirebilirsiniz.
Uzaktan izleme ve yönetim
Phoenix miner, uzaktan izleme ve yönetim için Claymore's dual miner protokolüyle tamamen
uyumludur. Bu, Claymore's dual miner'ı desteklemek için geliştirilmiş her aracı kullanabileceğiniz anlamına gelir;
Claymore's dual miner paketinin bir parçası olan "Remote manager" uygulaması da buna dahildir.
Uzaktaki veya yerel rig'leriniz üzerinde daha iyi kontrol ve madencilik kârınızı artırmak için
bazı benzersiz özellikler sunacak, çok daha güçlü ve güvenli uzaktan izleme ve kontrol işlevleri ile bir kontrol merkezi uygulaması
üzerinde çalışıyoruz.
Donanım kontrol seçenekleri
Donanım kontrol seçenekleriyle ilgili bazı önemli notlar:
En yeni Nvidia sürücüleri, donanım kontrolüne izin vermek için yönetici olarak (Linux'ta root olarak) çalıştırmayı gerektirir; bu nedenle VRAM timing seçeneklerinin çalışması için PhoenixMiner'ı yönetici olarak çalıştırmanız gerekir:
PhoenixMiner as administrator for the VRAM timing options to work.
VRAM timing seçeneklerini ("-straps", "-vmt1", "-vmt2", "-vmt3", "-vmr") kullanırken düşük değerlerle başlayın ve daha yüksek ve daha agresif ayarları denemeden önce kartların kararlı çalıştığından emin olun:
cards are stable before trying higher and more aggressive settings. You can use "-straps" along with the other options. For example "-straps 1" "-vmt1 60" will use the timings from 1st strap level but -vmt1 will be set to 60 instead of whatever value is specified by the 1st strap level. In such case the "-straps" option must be specified first.
Genel olarak "-vmt3" seçeneğinin hashrate üzerinde az etkisi vardır, bu yüzden önce diğer parametreleri ayarlamayı deneyin.
VRAM timing seçenekleri, GPU'lar aynı model olsa bile GPU'lar arasında oldukça farklı olabilir. Bu nedenle VRAM timing seçeneklerini GPU başına belirtebilirsiniz (ve muhtemelen belirtmelisiniz):
probably should) specify the VRAM timing options per-GPU.
Donanım kontrol seçenekleri Windows'ta hem AMD hem de Nvidia kartlar için desteklenir. Linux'ta seçeneklerin çoğu yalnızca AMD kartlar için desteklenir.
Tek bir değer belirtirseniz (ör. -cvddc 1150) tüm kartlarda kullanılır. Her kart için farklı değerleri şu şekilde belirtin (virgülle ayırarak): -cvddc 1100,1100,1150,1120,1090 Belirtilen değerler GPU sayısından azsa kalan GPU'lar varsayılan değerleri kullanır.
Yalnızca nispeten yeni AMD GPU'larda (RX460/470/480/560/570/580, Vega, Radeon VII, RX5700) test ettik. Daha eski GPU'larda sonuçlarınız farklı olabilir.
AMD'nin blockchain beta sürücüleri oldukça kararsız sonuçlar veriyor - voltajlar çoğu zaman hiç tutmuyor ya da bir süre sonra varsayılana geri dönüyor. En iyi sonuçlar için AMD'nin daha yeni sürücülerini kullanın: hataların çoğunun giderildiği 18.5.1 veya sonrası.
-tmax, GPU'nun (fanlar yetişemediği için) kısıtlamaya (throttle) başlaması gereken sıcaklığı belirtir.
Donanım kontrolü için başka programlar kullanıyorsanız çakışmalar mümkündür ve oldukça olasıdır. Voltajları vb. izlemek için GPU-Z gibi bir şey kullanın. MSI Afterburner da sorunsuz çalışıyor gibi görünüyor (böylece AMD kartlar PhoenixMiner tarafından kontrol edilirken Nvidia kartları onunla kontrol edebilirsiniz).
Bu açık olmalı ama yine de belirtelim: belirli frekanslar/voltajlar üçüncü taraf bir programla ayarlandığında çökmelere/donmalara/hatalı share'lere neden oluyorsa, PhoenixMiner donanım kontrol seçenekleriyle ayarlandığında da aynı derecede kararsız olacaktır.
PhoenixMiner'ın donanım kontrol seçenekleriyle sorun yaşıyorsanız ve daha önce frekansları, fanları ve voltajları kontrol etmek için memnun olduğunuz başka bir araç (MSI Afterburner, OverdriveNTool vb.) kullanıyorduysanız, muhtemelen en iyisi onu kullanmaya devam etmek ve PhoenixMiner'ın donanım kontrol seçeneklerini yok saymaktır (ya da yalnızca bazılarını kullanıp geri kalanını üçüncü taraf araçlarınızla ayarlamaya devam edin).
SSS
Q001: Neden bir madenci yazılımı daha?
A: We feel that the competition is good for the end user. In the first releases of PhoenixMiner we focused on the basic features and on the mining speed but we are now working on making our miner easier to use and even faster.
Q002: Aynı rig'de birden fazla PhoenixMiner örneği çalıştırabilir miyim?
A: Yes, but make sure that each GPU is used by a single miner (use the -gpus, -amd, or -nvidia
command-line options to limit the GPUs that given instance of PhoenixMiner actually uses).
Another possible problem is that all instances will use the default CDM remote port 3333,
which will prevent proper remote control for all but the first instance. To fix this problem,
use the -cdmport command-line option to change the CDM remote port form its default value.
Q003: PhoenixMiner'ı aynı rig'de diğer madenci yazılımlarıyla aynı anda çalıştırabilir miyim?
A: Yes, but see the answer to the previous question for how to avoid problems.
Q004: Bayat (stale) share nedir?
A: The ethash coins usually have very small average block time (15 seconds in most instances). On the other hand, to achieve high mining speed we must keep the GPUs busy so we can't switch the current job too often. If our rigs finds a share just after the someone else has found a solution for the current block, our share is a stale share. Ideally, the stale shares should be minimal as same pools do not give any reward for stale shares, and even these that do reward stale shares, give only partial reward for these shares. If the share is submitted too long after the block has ended, the pool may even fully reject it.
Q005: PhoenixMiner'ın bildirdiği bayat share yüzdesi neden havuzun gösterdiğinden
daha düşük?
A: PhoenixMiner can only detect the stale shares that were discovered after it has received a new job (i.e. the "very stale") shares. There is additional latency in the pool itself, and in the network connection, which makes a share stale even if it was technically found before the end of the block from the miner's point of view. As pools only reports the shares as accepted or rejected, there is no way for the miner to determine the stale shares from the pool's point of view.
Q006: Bir share bulunduğunda PhoenixMiner'ın gösterdiği "actual share difficulty" (gerçek share zorluğu)
ne anlama gelir?
A: It allows you to see how close you were to finding an actual block (a rare event these days for the most miners with reasonable-sized mining rigs). You can find the current difficulty for given coin on sites like whattomine.com and then check to see if you have exceeded it with your maximum share difficulty. If you did, you have found a block (which is what the mining is all about).
Q007: PhoenixMiner istatistiklerinde gösterilen "effective speed" (efektif hız) ne anlama gelir?
A: This is a measure of the actually found shares, which determines how the pool sees your miner hashrate. This number should be close to the average hashrate of your rig (usually a 2-4% lower than it) depending you your current luck in finding shares. This statistic is meaningless in the first few hours after the miner is started and will level off to the real value with time.
Q008: Havuzun gösterdiği efektif hashrate neden PhoenixMiner'ın gösterdiğinden düşük?
A: There are two reasons for this: stale shares and luck. The stale shares are rewarded at only about 50-70% by most pools. The luck factor should level itself off over time but it may take a few days before it does. If your effective hashrate reported by the pool is consistently lower than the hashrate of your rig by more than 5-7% than you should look at the number of stale shares and the average share acceptance time - if it is higher than 100 ms, try to find a pool that is near to you geographically to lower the network latency. You can also restart your rig, or try another pool.
Sorun giderme
P001: AMD RX470/480/570/580 veya benzeri bir kart kullanıyorum ve son birkaç ayda Ethereum ve Ethereum Classic'te
hashrate'im ciddi şekilde düştü!
S: This is known problem with some cards. For the newer cards (RX470/480/570/580), this can be
solved by using the special blockchain driver from AMD (or try the latest drivers, they may
incorporate the fix). For the older cards there is no workaround but you still can mine EXP,
Musicoin, UBQ or PIRL with the same speed that you mined ETH before the drop.
P002: Nvidia GTX9x0 kartım Windows 10'da çok düşük hashrate gösteriyor!
S: While there is a (convoluted) workaround, the best solution is to avoid Windows 10
for these cards - use Windows 7 instead.
P003: Nvidia GTX970 (veya benzeri) bir kart kullanıyorum ve Ethereum ya da
Ethereum Classic'te hashrate'im dramatik şekilde düştü!
S: GTX970 has enough VRAM for larger DAGs but its hashate drops when the DAG size starts
to exceed 2 GB or so. Unlike the AMD Polaris-based cards, there is no workaround for this
problem. We recommend using these cards to mine EXP, Musicoin, UBQ or PIRL with the same speed
that you used to ETH before the drop.
P004: Windows Uzak Masaüstü (RDP) kullanırken kartlarımın bazılarını (veya fan hızlarını ve sıcaklıklarını) göremiyorum!
S: This is a known problem with RDP. Use VNC or TeamViewer instead.
P005: Windows 10'da PhoenixMiner konsolunun içine tıklarsanız donuyor!
S: This is a known problem on Windows 10, related to so called "Quick Edit" feature of the command
prompt window. From PhoenixMiner 2.6, the QuickMode is disabled by default, so you shouldn't experience
this problem. If you still, do, read here how to solve it: https://stackoverflow.com/q/33883530
P006: PhoenixMiner başlatıldıktan hemen sonra çalışmayı durduruyor ve son mesaj "debugger detected" oluyor
S: If you have only Nvidia cards, add the option -nvidia to the PhoenixMiner.exe command line.
If you have only AMD cards, add the option -amd to the command line.
P007: PhoenixMiner DAG tamponunu ayırdıktan sonra bir hata gösteriyor ve kapanıyor.
S: If you have more than one GPU, make sure that your Windows page file minimal size is set to at
least (N x DS + 4) GB, where N is the number of GPUs, and DS is the size of DAG in GB (about 2.9 GB around
January 2019 for ETC and ETH). For example, if you have 10 GPUs, you need 10 x 2.9 + 4 = 33 GB minimal
size of the page file. Note that this will increase as the DAG sizes increase. If you are using -clkernel 3, for each GPU add size of
the DAG twice instead of once (e.g. for 3 GPUs mining with -clkenel 3 you will need 3 x 2 x 2.9 + 4 = 21.4 GB minimal page file size)
P008: Madenci yazılımı DAG epoch'u değiştiğinde bazen çöküyor.
S: During DAG generation, the GPUs are loaded more than during the normal operation. If you have
overclocked or undervolted the GPUs "to the edge", the DAG generation ofter pushes them "over the
edge". Another possible reason for the crash (especially if the whole rig crashes) is the higher
power usage during this process. You can lower the DAG generation speed by specifying the -lidag
command-line option. The possible values are 0 (no slow down), 1, 2, and 3 (max slowdown).
In order to check if your rig would be stable during DAG generation, run it in benchmark mode
by specifying the -bench 210 command line option. Then every time when you press the key 'd'
the miner will advance to the next DAG epoch, and you will be able to see if it is stable during
multiple DAG generations. If it isn't you can try to alter the -lidag and -eres command line options
until the desired stability is achieved.
P009: Madenci yazılımı ETC veya ETH kazarken DAG tamponunu oluşturamıyor
S: The versions of PhoenixMiner before 4.2 only support DAG epoch up to 265. Both ETC and ETH has reached epoch 266 already. To ensure uninterrupted operation, please upgrade to 4.2.
PhoenixMiner 4.2 supports DAG epoch up to 330, and PhoenixMiner 4.5 supports DAG epoch up to 450.
